Colossus ComputerDigital modules
In early 1958 DEC shipped its first products, the "Digital Laboratory Module" line. The Modules consisted of a number of individual electronic components and germanium transistors mounted to a circuit board, the actual circuits being based on those from the TX-2.
The Laboratory Module were packaged in an extruded aluminum housing, intended to sit on an engineer's workbench. They were then connected together using banana plug patch cords inserted at the front of the modules. Three versions were offered, running at 5 MHz (1957), 500 kHz (1959), or 10 MHz (1960). The Modules proved to be in high demand in other computer companies, who used them to build equipment to test their own systems. Despite the recession of the late 1950s, the company sold $94,000 worth of these modules during 1958 alone, turning a profit at the end of its first year.
The original Laboratory Modules were soon supplemented with the "Digital Systems Module" line, which were identical internally but packaged differently. The Systems Modules were designed with all of the connections at the back of the module using 22-pin Amphenol connectors, and were attached to each other by inserting them into a custom 19-inch rack. These versions allowed 25 modules be to inserted into a single 5-1/4 inch section of racking, and allowed the high densities needed to build a computer. DEC used the Systems Modules to build their "Memory Test" machine for testing core memory systems, selling about 50 of these pre-packaged units over the next eight years.
Modules were part of DEC's product line into the 1970s, although they went through several evolutions during this time as technology changed. The same circuits were then packaged as the first "R" (red) series "Flip-Chip" modules. Later, other module series provided additional speed, much higher logic density, and industrial I/O capabilities. Digital published extensive data about the modules in free catalogs that became very popular.
With the company established and a successful product on the market, DEC turned its attention to the computer market once again as part of its planned "Phase II". In August 1959, Ben Gurley started design of the company's first computer, the PDP-1. In keeping with Doriot's instructions, the name was an initialism for "Programmable Data Processor", leaving off the term "computer". As Gurley put it, "We aren't building computers, we're building 'Programmable Data Processors'." The prototype was first shown publicly at the Joint Computer Conference in Boston in December 1959.
The PDP-1 design was based on a number of System Building Blocks packaged into several 19-inch racks to form an 18-bit word computer, supplied standard with 4 kWords of core memory and running at a basic speed of 100,000 operations per second. The racks were themselves packaged into a single large mainframe case, with a hexagonal control panel containing switches and lights mounted to lay at table-top height at one end of the mainframe. Above the control panel was the system's standard input/output solution, a punch tape reader and writer. Most systems were purchased with two peripherals, the Type 30 vector graphics display, and a Soroban Engineering modified IBM Model B Electric typewriter that was used as a printer. The Soroban system was notoriously unreliable, and often replaced with a modified Friden Flexowriter, which also contained its own punch tape system. A variety of more-expensive add-ons followed, including magnetic tape systems, punched card readers and writers, and faster punch tape and printer systems.
The first PDP-1 was delivered to Bolt, Beranek and Newman in November 1960, and formally accepted the next April. In 1962 DEC donated the prototype PDP-1 to MIT, where it was placed in the room next to the TX-0. In this setting the PDP-1 quickly replaced the TX-0 as the favourite machine among the budding hacker culture, and served as the platform for a wide variety of "firsts" in the computing world. Perhaps best known among these is the first computerized video game, Spacewar!, but among the list are the first text editor, word processor, interactive debugger, the first credible computer chess program, and some of the earliest computerized music.
The PDP-1 sold in basic form for $120,000, or about $780,000 in 2005-era USD.[ BBN's system was quickly followed by orders from Lawrence Livermore and Atomic Energy of Canada (AECL), and eventually 53 PDP-1s were delivered until production ended in 1969. All of these machines were still being actively used in 1970, and several were eventually saved. MIT's example was donated to The Computer Museum, Boston, and from there ended up at the Computer History Museum (CHM). A late version of Spacewar! on paper tape was still tucked into the case. PDP-1 #44 was found in a barn in Wichita, Kansas in 1988, apparently formerly owned by one of the many aviation companies in the area, and rescued for the Digital Historical Collection, also eventually ending up at the CHM. AECLs was sent to Science North, but was later scrapped.
When DEC introduced the PDP-1, they also mentioned larger machines at 24, 30 and 36-bits, based on the same design. During construction of the prototype PDP-1, some design work was carried out on a 24-bit PDP-2, and the 36-bit PDP-3. Although the PDP-2 never proceeded beyond the initial design, the PDP-3 found some interest and was designed in full. Only one PDP-3 appears to have been built, in 1960, by the CIA's Scientific Engineering Institute (SEI) in Waltham, Massachusetts. According to the limited information available, they used it to process radar cross section data for the Lockheed A-12 reconnaissance aircraft. Gordon Bell remembered that it was being used in Oregon some time later, but could not recall who was using it.
In November 1962 DEC introduced the $65,000 PDP-4. The PDP-4 was similar to the PDP-1 and used a similar instruction set, but used slower memory and different packaging to lower the price. Like the PDP-1, about 54 PDP-4's were eventually sold, most to a customer base similar to the original PDP-1.
In 1964 DEC introduced its new Flip Chip module design, and used it to re-implement the PDP-4 as the PDP-7. The PDP-7 was introduced in December 1964, and about 120 were eventually produced. An upgrade to the Flip Chip led to the R series, which in turn led to the PDP-7A in 1965. The PDP-7 is most famous as the original machine for the Unix operating system.
A more dramatic upgrade to the PDP-1 series was introduced in August 1966, the PDP-9.[26] The PDP-9 was instruction compatible with the PDP-4 and -7, but ran about twice as fast as the -7 and was intended to be used in larger deployments. At only $19,900 in 1968, the PDP-9 was a big seller, eventually selling 445 machines, more than all of the earlier models combined.
Even while the PDP-9 was being introduced, its replacement was being designed, and was introduced as 1969's PDP-15, which re-implemented the PDP-9 using integrated circuits in place of modules. Much faster than the PDP-9 even in basic form, the PDP-15 also included a floating point unit and a separate input/output processor for further performance gains. Over 400 PDP-15's were ordered in the first eight months of production, and production eventually amounted to 790 examples in twelve basic models. However, by this time other machines in DEC's lineup could fill the same niche at even lower price points, and the PDP-15 would be the last of the 18-bit series.
In 1962, Lincoln Laboratory used a selection of System Building Blocks to implement a small 12-bit machine, and attached it to a variety of analog-to-digital (A to D) input/output (I/O) devices that made it easy to interface with various analog lab equipment. The LINC proved to attract intense interest in the scientific community, and has since been referred to as the first real minicomputer, a machine that was small and inexpensive enough to be dedicated to a single task even in a small lab.
Seeing the success of the LINC, in 1963 DEC took the basic logic design but stripped away the extensive A to D systems to produce the PDP-5. The new machine, the first outside the PDP-1 mould, was introduced at WESTCON on 11 August 1963. A 1964 ad expressed the main advantage of the PDP-5, "Now you can own the PDP-5 computer for what a core memory alone used to cost: $27,000" 116 PDP-5s were produced until the lines were shut down in early 1967. Like the PDP-1 before it, the PDP-5 inspired a series of newer models based on the same basic design that would go on to be more famous than its parent.
On 22 March 1965, DEC introduced the PDP-8, which replaced the PDP-5's modules with the new R-series modules using Flip Chips. The machine was re-packaged into a small tabletop case, which remains distinctive for its use of smoked plastic over the CPU which allowed one to easily see the wire-wrapped internals of the CPU. Sold standard with 4 kWords of 12-bit core memory and a ASR-33 Teletype for basic input/output, the machine listed for only $18,000. The PDP-8 is referred to as the first real minicomputer because of its sub-$25,000 price. Sales were, unsurprisingly, very strong, and helped by the fact that several competitors had just entered the market with machines aimed directly at the PDP-5's market space, which the PDP-8 trounced. This gave the company two years of unrestricted leadership, and eventually 1450 "straight eight" machines were produced before it was replaced by newer implementations of the same basic design.
DEC hit an even lower price-point with the PDP-8/S, the S for "serial". As the name implies the /S used a serial arithmetic unit, which was much slower but reduced costs so much that the system sold for under $10,000. DEC then used the new PDP-8 design as the basis for a new LINC, the two-processor LINC-8. The LINC-8 used one PDP-8 CPU and a separate LINC CPU, and included instructions to switch from one to the other. This allowed customers to run their existing LINC programs, or "upgrade" to the PDP-8, all in software. Although not a huge seller, 142 LINK-8s were sold starting at $38,500. Like the original LINC to PDP-5 evolution, the LINC-8 was then modified into the single-processor PDP-12, adding another 1000 machines to the 12-bit family. Newer circuitry designs led to the PDP-8/I and PDP-8/L in 1968.[11] In 1975, one year after an agreement between Digital and Intersil, the Intersil 6100 chip was launched, effectively a PDP-8 on a chip. This was a way to allow PDP-8 software to be run even after the official end-of-life announcement for the Digital PDP-8 product line.
While the PDP-5 introduced a lower-cost line, 1963's PDP-6 was intended to take DEC into the mainframe market with a 36-bit machine. However, the PDP-6 proved to be a "hard sell" with customers, as it offered few advantages over similar machines from the better established vendors like IBM or Honeywell, in spite of its low cost around $300,000. Only 23 were sold,[36] or 26 depending on the source, and unlike earlier models the low sales meant the PDP-6 was not improved with intermediate versions. However, the PDP-6 is historically important as the platform that introduced "Monitor", an early time-sharing operating system that would evolve into the widely used TOPS-10.
In spite of the PDP-6's limited commercial success, it introduced many features that clearly had commercial benefit. When the Flip Chip packaging allowed the PDP-6 to be re-implemented at a much lower cost, DEC took the opportunity to carry out a similar evolution of their 36-bit design and introduced the PDP-10 in 1968. The PDP-10 was as much a success as the PDP-6 was a failure; during its lifetime about 700 mainframe PDP-10's were sold before production ended in 1984. The PDP-10 was widely used in university settings, and thus was the basis of many advances in computing and operating system design during the 1970s. DEC later re-branded all of the models in the 36-bit series as the "DECsystem-10", and PDP-10's are generally referred to by the model of their CPU, like "KA10". Later upgrades produced the compatible DECSYSTEM-20, along with TOPS-20 that included virtual memory.
One of the most unusual peripherals produced for the PDP-10 was the DECtape. The DECtape was a length of standard magnetic tape wound on 5-in reels. However, the recording format was a 10-track approach using fixed-length numbered 'blocks' organized into a standard file structure, including a directory. Files could be written, read, changed, and deleted on a DECtape as though it were a disk. In fact, some PDP-10 systems had no disks at all, using DECtapes alone for their primary data storage. For greater efficiency, the DECtape drive could read and write to a DECtape in both directions.
In 1968 DEC was working on a PDP machine that would be based on 8-bit bytes instead of 6-bit characters. Known as the "PDP-X", the project was eventually cancelled. Several team members decamped and set up Data General in May 1968, and rapidly brought the 16-bit NOVA minicomputer to market. DEC immediately found itself behind in the industry transition to 8-bit bytes, and soon lost its crown as the largest minicomputer vendor.
The PDP-11 16-bit computer was designed in a crash program by Harold McFarland, Gordon Bell, Roger Cady, and others. The project was able to leap forward in design with the arrival of Harold McFarland, who had been researching 16-bit designs at Carnegie Mellon University. One of his simpler designs became the PDP-11, although when they first presented it, management was not impressed and almost cancelled it.
In particular, the new design did not include many of the addressing modes that were intended to make programs smaller in memory, a technique that was widely used on other DEC machines and CISC designs in general. This would mean the machine would spend more time accessing memory, which would slow it down. However, the machine also introduced the idea of "General Registers", which gave the programmer flexibility to use these high-speed memory caches as they needed, potentially addressing the performance issues.
A major advance in the PDP-11 design was UNIBUS, which supported all peripherals through memory mapping. This allowed new devices to be added easily, generally only requiring some sort of hardware interface and then writing software that examined the mapped memory to control them. This spawned a huge market of 3rd party add-ons for the PDP-11, which made the machine even more useful.
Its numerous architectural innovations proved superior to all competitors and the "11" architecture was soon the industry leader, propelling DEC back to their leadership position. The design was later expanded to allow paged physical memory and memory protection features, useful for multitasking and time-sharing, and some models supported separate instruction and data spaces for an effective virtual address size of 128 kB within a physical address size of up to 4 MB. PDP-11s, implemented as single-chip CPUs, continued to be produced until 1996, by which time over 600,000 had been sold.
The PDP-11 supported several operating systems, including Bell Labs' new Unix operating system as well as DEC's DOS-11, RSX-11, IAS, RT-11, DSM-11, and RSTS/E. Many early PDP-11 applications were developed using standalone paper-tape utilities. DOS-11 was the PDP-11's first disk operating system, but was soon supplanted by more capable systems. RSX provided a general-purpose multitasking environment and supported a wide variety of programming languages. IAS was a time-sharing version of RSX-11D. Both RSTS and Unix were time-sharing systems available to educational institutions at little or no cost, and these PDP-11 systems were destined to be the sandbox for a generation of engineers and computer scientists. Large numbers of 11/70s were deployed in telecommunications and industrial control applications. AT&T became DEC's largest customer.
RT-11 provided a practical real-time operating system, allowing the PDP-11 to continue Digital's critical role as a computer supplier for embedded systems. RT-11 served as the inspiration for many microcomputer OS's, as these were generally being written by programmers who cut their teeth on one of the many PDP-11 models. CP/M used a command syntax similar to RT-11's, and even retained the awkward PIP program used to copy other programs. DEC's use of "/" for "switches" (command-line options) would lead to the adoption of "\" for pathnames in MS-DOS and Microsoft Windows as opposed to "/" in Unix.
The evolution of the PDP-11 followed earlier systems, eventually evolving into a single-user deskside personal computer form in the microPDP. 600,000 PDP-11's of all models were eventually sold. Many PDP-11-like machines were also introduced, and a wide variety of peripheral vendors entered the ecosystem. The PDP-11 series was cloned in COMECON countries as the SM EVM series, and was produced in quantities comparable to original PDP-11 production.
In 1976, DEC decided to extend the PDP-11 architecture to 32-bits while adding a complete virtual memory system to the simple paging and memory protection of the PDP-11. The result was the VAX architecture. The first computer to use a VAX CPU was the VAX-11/780, which DEC referred to as a superminicomputer. Although it was not the first 32-bit minicomputer, the VAX-11/780's combination of features, price, and marketing almost immediately propelled it to a leadership position in the market after it was released in 1978. VAX systems were so successful that in 1983, DEC canceled its Jupiter project, which had been intended to build a successor to the PDP-10 mainframe, and instead focused on promoting the VAX as their the single computer architecture for the company.
Supporting the VAX's success was the VT52, one of the most successful smart terminals. Building on earlier less successful models (the VT05 and VT50), the VT52 was the first terminal that did everything one might want in a single chassis. The VT52 was followed by the even more successful VT100 and its follow-ons, making DEC one of the largest terminal vendors in the industry. With the VT series, DEC could now offer a complete top-to-bottom system from computer to all peripherals, which formerly required collecting the required devices from different suppliers.
The VAX processor architecture and family of systems evolved and expanded through several generations during the 1980s, culminating in the NVAX microprocessor implementation and VAX 7000/10000 series in the early 1990s
